Replace the * in the suffix with the required length in whole feet, the maximum length is 3.6576 m (12').
For totalizing in liters with 1 liter resolution, the max count would be 999999.įor a Remote Display, add suffix "-RD-*FT" to the model number, add $210 to the price. Examples: For totalizing in liters with 1/100 liter resolution, the max count would be 9999.99. Please specify the desired range in SCFH.įor totalizer option, add suffix "-TOT" to the model number, add $120 to the price. For an alternate output scale add suffix "-T" to the model number for temperature or "-P" for pressure, no additional cost.įor units scaled in SCFH, add suffix "-SCFH" to model number, no additional cost. Optional secondary output are scaled the same as the primary output scale. Standard input is 0-5V, for optional 4-20 mA input add suffix "-IN" to the model number, no additional cost. To replace the standard RS232 communications with RS485, add suffix "-RS485" to the model number, add $120 to the price. *Specify gas, and inlet/outlet or backpressure for custom calibrations.Ĭalibrations done at ambient (25☌/77☏) temperature only. Standard units are calibrated to air 5 psig for 0 to 1 LPM, 15 psig for 2 to 10 LPM, 30 psig for 20 to 100 LPM, and 50 psig for 200 LPM and greater.įor custom calibrations, add "-(*)" to the model number, no additional cost. Note: Comes complete with 24 Vdc universal power supply, 1.8 m (6') cable, 8-pin male Mini- DIN connector, operator's manual, and NIST certificate. † All prices on this site are shown in Singapore Dollars. Supply Voltage: 15 to 30 Vdc for units 2 SLM and smaller 24 to 30 Vdc for units 5 SLM and largerĮlectrical Connections: 8-pin circular mini DIN Supply Current: 0.250 A for 20 SLM and under 0.75 A for 50 SLM and above (typical) The recommended maximum operating pressure is 15 psig They are designed for near atmospheric pressure conditions only. Volumetric flow meters and controllers not certified for accuracy at mass flow rates above the rated flow range of the meter. To Use in Volumetric Mode: Near atmosphere, 15 psig recommended maximum. LSS (Option):316LSS, 303SS, 430FRSS, Perfluoroelastomer standard, FKM, EPDM, Buna, Neoprene Wetted Materials: Standard: 303 and 302 SS, FKM, silicone RTV (rubber), glass-reinforced nylon, aluminum, brass, 410 SS, silicone, glass >250 SLM: 416 SS and nickel replace brass Humidity Range: 0 to 100% RH, non-condensing Optional Input/Outputs: 4 to 20 mA, 0 to 10 Vdc
#IBM I2 ANALYST NOTEBOOK PRICE IN PH SERIAL#
Same serial connection to a distance of 46 m (150'). It is also possible to multi-drop up to 26 units on the Viewed or recorded through the RS232 connection. Volumetric flow, massįlow, absolute pressure, and temperature can all be Setpoints can be adjusted from the front keypad or Standard units include aĠ to 5V output (4 to 20 mA optional) and RS232Ĭommunications. To the flow body to control flow using the integral The controller uses a true proportional valve coupled This standardizedįlow rate is commonly called the mass flow rateĪnd is reported in units such as standard cubicĬentimeters per minute (SCCM) or standard liters
Separate absolute temperature and pressure sensorsĪre incorporated and correct the volumetric flow rate Used to accurately determine the volumetric flow rate. This, along with the viscosity of the gas, is
Measure the pressure drop along a fixed distance of A differential pressure sensor is used to Volumetric flow rate be linearly related to the pressureĭrop. Region, the Poiseuille equation dictates that the The principle of differential pressure within a laminarįlow field to determine and control mass flow rate.Ī laminar flow element (LFE) inside the meter forces
#IBM I2 ANALYST NOTEBOOK PRICE IN PH SERIES#
The FMA-LP2600A Series mass flow controllers use